The Meizu M6 Note has three RAM/ROM variants, 3GB RAM/ 16GB storage, 3GB RAM/ 32GB storage, and 4GB RAM/ 64GB storage. The phone models will be made available by the company at CNY 1,099, CNY 1,299, and CNY 1,699.
The highlight feature on the Meizu M6 Note, the dual camera setup consists of a 12-megapixel primary sensor (6P lens) with f/1.9 aperture and a 5-megapixel secondary sensor with f/2.0 aperture size. At front, the phone comes with a 16-megapixel shooter with f/2.0 aperture and 5P lens.
The Meizu M6 Note runs Flyme OS 6 UI based on Android 7.1.2 Nougat and sports a 5.5-inch full-HD (1080×1920 pixels) display. As mentioned earlier, the handset is powered by an octa-core Snapdragon 625 SoC. It comes with a fingerprint sensor embedded in the home button at the front of the handset.
The phone packs a 4000mAh battery, it measures 154.6×75.2×8.35mm and weighs 173 grams. The connectivity options offered by the Meizu M6 Note include 4G VoLTE connectivity, Bluetooth 4.2, Wi-Fi 802.11ac, and GPS.
For the freshest produce, find us on Facebook for the latest teardown news.
Remove the SIM card tray, the phone support TF Card expansion.
Remove two screws close to the Micro USB port.
Insert a pick under the display assembly. Slide the pick to unlock all the snaps that securing the back cover.
Now you can separate the back cover from the phone.
We can see the internal structure of the Meizu M6 Note, and it uses the common three-stage design, the motherboard and sub-board using BTB connection.
Then we first look at the anti-bump design of the back cover, and it can be seen that the corner has been thickened with injection molding, the metal is relatively thin, bearing mainly depended on the layer thickness of injection molding.
In the corresponding position of the battery, it is using a graphite sticker to improve heat dissipation.
The key seal is better, the bottom of the keycap has a rubber gasket.
The components on the front side of the motherboard are more closely. In addition to the coaxial connector, all of the other connectors are fixed by the metal shield, only a small chip on the right side is not covering by the metal shield. The other chips are covered by the metal shield.
Remove the metal plate and disconnect three connectors from the motherboard.
When all the connectors are disconnected, the motherboard will be easy to remove. There are many components using metal contacts to connect to the motherboard, such as the key button, handset, and even including screen touch cable.
Here are the touch screen cable and the motherboard connected metal contacts, because the amount of information transmitted relatively large, so there are as many as eight contacts.
At the top of the double photo is composed of four LED flash, you can see both sides of the warm colors, the middle two cold color LED flash. The overall space utilization of the main board is higher.
The dual camera setup consists of a 12-megapixel primary sensor (6P lens) with f/1.9 aperture (Sony IMX362) and a 5-megapixel secondary sensor with f/2.0 aperture size.
The phone comes with a 16-megapixel front camera with f/2.0 aperture and 5P lens.
Below the shield is the RF amplifier chip and the power management chip.
Then we began to dismantle the lower part of the fuselage, the first separate the fixed screws.
Here’s Meizu M6 Note loudspeaker.
Then you can use the pick to lift up the bottom board. You can see the headphone jack and Micro USB port are integrated here.
The back of the board has a microphone.
In the data port location, we can see the rubber seal, and headphone jack seal is relatively simple.
With bottom board removed, you can see the mTouch button. We first remove a plastic gasket, key button and fingerprint identification assembly are integrated into the keycap.
The battery comes from ATL, and with a capacity of 3940mAh, 15.17Wh.
